Enetwork PT.Practise SBA 2
A few things to keep in mind while
completing this activity:
1.
Do not
use the browser Back button or close or reload any exam
windows during the exam.
2.
Do not
close Packet Tracer when you are done. It will close automatically.
3.
Click
the Submit Assessment button to submit your work.
4.
Introduction
In this practice Packet Tracer Skills
Exam, you will:
·
design
and implement an addressing scheme to meet stated requirements
·
configure,
verify, and troubleshoot connectivity between all devices in the network
Addressing
Table
Device
|
Interface
|
Address
|
Subnet Mask
|
Default Gateway
|
Router1
|
Fa0/0
|
172.16.1.1
|
255.255.255.224
|
n/a
|
Fa0/1
|
172.16.1.33
|
255.255.255.240
|
n/a
|
|
Switch1
|
VLAN1
|
172.16.1.2
|
255.255.255.224
|
172.16.1.1
|
PC1
|
NIC
|
172.16.1.30
|
255.255.255.224
|
172.16.1.1
|
PC2
|
NIC
|
Preconfigured
(172.16.1.35)
|
Preconfigured
(255.255.255.240)
|
Preconfigured
(172.16.1.33)
|
NOTE: The initial network has some errors.
To aid in configuring and verifying the devices, as well as in troubleshooting
the existing errors, use a printed version of these instructions to fill in the
missing address information in the table during Step 1.
Step 1: Determine the IP Addressing Scheme.
Design an addressing scheme and fill in
the Addressing Table based on the following requirements:
a. Subnet the address space 172.16.1.0/24 to
provide 30 host addresses for LAN 1 while wasting the least amount of address space.
b. Assign the first available subnet to LAN
1.
c. Assign the lowest (first) host address in
this subnet to the Fa0/0 interface on Router1.
d. Assign the second address in this subnet
to the VLAN 1 interface on Switch1.
e. Assign the highest (last) host IP address
in this subnet to PC1.
Step 2: Configure Router1.
a. Configure Router1 with these basic
parameters:
· Use Router1 as the
router name.
· Use class as the
encrypted password for privileged EXEC mode.
· Require password-protected logins for the
console line. Use cisco as the password.
· Require password-protected logins for the
vty lines. Use cisco as the password.
· Configure the banner message-of-the-day as Authorized
access only!
b. Configure the two Fast Ethernet
interfaces.
· Configure the router interfaces according
to your completed addressing table.
· Configure each interface with a
description.
c. Close the terminal window after completing
the router configuration.
Step 3: Configure Switch1 and Verify
Connectivity.
a. Remove the console connection between PC1
and Router1.
b. Connect PC1 to the Switch1 console port.
c. Configure Switch1 with these basic parameters:
· Use Switch1 for the
switch name.
· Use class as the
encrypted password for privileged EXEC mode.
· Require password-protected logins for the
console line. Use cisco as the password.
· Require password-protected logins for the
vty lines. Use cisco as the password.
· Configure the banner message-of-the-day asAuthorized
access only!
d. Configure interface VLAN 1.
e. Configure the default gateway.
f. Test that Switch1 is able to ping the
default gateway.
Step 4: Configure and Verify PC1
Addressing.
a. Use the IP addressing you determined in
Step 1 and configure PC1 with the correct addressing.
b. Test that PC1 is able to ping the default
gateway.
Step 5: Verify and Troubleshoot End-to-End
Connectivity.
Verify that PC1 is able to ping PC2. If
the ping fails, locate and correct any errors. For example, make sure PC2 is
configured correctly with appropriate addressing for the subnet it belongs to.
Packet Tracer Image:
Step 2: Configure Router1.
Router>enable
Router#configure
terminal
Enter configuration
commands, one per line. End with CNTL/Z.
Router(config)#hostname
Router1
Router1(config)#enable
secret class
Router1(config)#line
console 0
Router1(config-line)#password
cisco
Router1(config-line)#login
Router1(config-line)#exit
Router1(config)#line
vty 0 4
Router1(config-line)#password
cisco
Router1(config-line)#login
Router1(config-line)#exit
Router1(config)#banner
motd #Authorized access only!#
Router1(config)#interface
fastEthernet 0/0
Router1(config-if)#ip
address 172.16.1.1 255.255.255.224
Router1(config-if)#description
LAN1
Router1(config-if)#no
shutdown
Router1(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/0, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/0, changed state to up
Router1(config-if)#exit
Router1(config)#interface
fastEthernet 0/1
Router1(config-if)#ip
address 172.16.1.33 255.255.255.240
Router1(config-if)#description
LAN2
Router1(config-if)#no
shutdown
Router1(config-if)#
%LINK-5-CHANGED:
Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface FastEthernet0/1, changed state to up
Router1(config-if)#do
write
Building
configuration...
[OK]
Router1(config-if)#
Step 3: Configure Switch1 and Verify
Connectivity.
Switch>enable
Switch#configure
terminal
Enter configuration
commands, one per line. End with CNTL/Z.
Switch(config)#hostname
Switch1
Switch1(config)#enable
secret class
Switch1(config)#line
console 0
Switch1(config-line)#password
cisco
Switch1(config-line)#login
Switch1(config-line)#exit
Switch1(config)#line
vty 0 4
Switch1(config-line)#password
cisco
Switch1(config-line)#login
Switch1(config-line)#exit
Switch1(config)#banner
motd #Authorized acccess only!#
Switch1(config)#interface
vlan 1
Switch1(config-if)#ip
address 172.16.1.2 255.255.255.224
Switch1(config-if)#no
shutdown
Switch1(config-if)#
%LINK-5-CHANGED:
Interface Vlan1, changed state to up
%LINEPROTO-5-UPDOWN:
Line protocol on Interface Vlan1, changed state to up
Switch1(config-if)#exit
Switch1(config)#ip
default-gateway 172.16.1.1
Switch1(config)exit
Switch1#write
Building
configuration...
[OK]
Switch1#ping
172.16.1.1
Type escape sequence
to abort.
Sending 5, 100-byte
ICMP Echos to 172.16.1.1, timeout is 2 seconds:
!!!!!
Success rate is 100
percent (5/5), round-trip min/avg/max = 2/17/38 ms
Switch1#
0 komentar:
Posting Komentar